Steel materials

Tool Steel W1 - Tool Steel W1 Forgings All Metals AISI O1 Special Oil Steel

The W series of tool steels are a very simple alloy group, low cost, and responsive to simple heating and water quenching for hardening. The alloy does undergo considerable distortion during quenching. To Send a Request for Quote, please Click Here, call 973.276.5000, or fax (973) 276 5050.The Sousa Corp Tool Steel ReferenceTool Steel Composition. Water Hardening Cold Work. Shock Resisting. Oil Hardening Cold Work. Air Hardening, Medium Alloy Cold Work. High Carbon, High Chromium Cold Work. Low Alloy Special Purpose. Chromium Hot Work. Tungsten Hot Work.Shenzhen NewAsia Steel Co. LinkedInWe are producer and large stockist of special steel in China. Our main products as below 1. Alloy Structure Steel AISI 4140, 4340, 8620, 9840, 4130, 4145H, etc. 2.

OHNS Round Bar, Din 1.2510 Rod, Aisi O1 Tool Steel AISI O1 Special Oil Steel

buy OHNS Round Bar in India from OHNS Steel Material suppliers at Low Cost in India. check Din 1.2510 Rod, OHNS Die Steel Bar, OHNS 01 Steel Square Bars, Forged Rods, Aisi O1 Tool Steel Metal Stock, Inc. , Flat Stock - L. S. Starrett CompanyStarrett Ground Flat Stock is produced in Regular (+/-.001" Thickness & Square) and Oversized (+010/.015" Thickness & Square) in 18 24 and 36 lengths out of the following materials O1, A2, D2, A6 tool steel and Low Carbon Steel with a surface finish down to

Compari of wear properties of tool steels AISI D2 and AISI O1 Special Oil Steel

The sample AISIO1 steel, which was nitrided for 6 hours, exhibited a hardness about 46% higher than the one measured for the untreated sample. This sample also showed the thicker layer, with a AISI O1 Special Oil SteelCompari of wear properties of tool steels AISI D2 and AISI O1 Special Oil SteelJun 01, 2006Two commercial cold work tool steels, AISI D2 and O1, were heat treated in order to obtain the same hardness 700. HV (60 HRc) and were subsequently tested in three different modes of wear, namely in adhesion, three-body and two-body abrasion, by using pin-on-disk, dry sand/rubber wheel apparatus and pin abrasion on SiC, respectively.. Even though AISI O1 and D2 steel are heat China AISI 420/JIS SUS420J2/DIN 1.2083 Stainless Steel AISI O1 Special Oil SteelTool Steel Bar, Die Steel Bars, Round Steel Bar manufacturer / supplier in China, offering AISI 420/JIS SUS420J2/DIN 1.2083 Stainless Steel Round Bar, Forged Agehardening Steel for Plastic Mould Fast Delivery 1.2311 AISI P20/P20+Ni Plastic Mold Steel Plate, Forged Plastic Tool Steel Blocks Forged Steel P20 P40 Alloy Steel Forged Round Bars and so on.

Carbon Steels Stainless Steels - Engineering Steels

O1 AISI O1 DIN 1.2510 Medium alloyed cold work steel, good hardening capacity, high wear resistance, for cutting and punching tools, shear knives, thread rolling and measuring tools. P20 AISI P20 DIN 1.2311 Plastic mould steel, supplied in the HT condition, for plastic moulds, frames for pressure dies, hydro forming tools, can be nitrided. S1 AISI O1 Special Oil SteelBarra Redonda Da Liga Aisi O1 Ferramenta De Aço - Buy O1 AISI O1 Special Oil SteelBarra Redonda Da Liga Aisi O1 Ferramenta De Aço , Find Complete Details about Barra Redonda Da Liga Aisi O1 Ferramenta De Aço,O1 Aço,Aisi O1 Aço,Aço Ferramenta O1 from Steel Round Bars Supplier or Manufacturer-Huangshi Kangheng Industrial Corporation LimitedAISI O1/DIN 1.2510/JIS SKS3 Tool Steel Round Bar Best AISI O1 Special Oil SteelType O1 oil-hardening cold-work steel consists of chromium, manganese, and tungsten and is relatively inexpensive. Fabrication and Heat Treatment Machinability The machinability of O1 steels is very good with a rating of 90% that of water hardening low alloy steels. Forming:

AISI O1 Tool Steel AISI O1 Die Steel AISI O1

AISI O1 is equivalent of DIN 2510 Tool Steel is the oil-hardening, non-shrinking tool steel, good cutting edge retention; high harden ability and dimensional stability during heat treatment. Physical PropertiesAISI O1 Special Oil Steelaisi 01 steel specificationo1 tool steel specificationo1 tool steel propertieso 1 steel propertieso 1 tool steel specso1 steel compositiona2 tool steel for sale01 tool steel propertiesAISI D5 tool steelThe heat-softening temperature is 520°C. The cross-sectional dimension can be completely hardened below 400mm. The wear resistance of the steel is 3 to 4 times higher than that of the low-alloy tool steel. The net fire volume is less deformed. Hard depth oil array 200 ~ 300mm.

42CrMo Steel Round Bar Sheet Plate Material - gshun Steel

42CrMo Steel Round Bar Sheet Plate Material. 42CrMo Steel Material is high strength steel. It has great toughness, strength and hardenability. After quenching and tempering treatment, it will get better fatigue limit and shock resistance ability. It usually is used without obvious temper embrittlement after the quenching and tempering treatment.

    Leava a Message: